Sprinkler use and precautions 1. Requirements for water When the sprinkler uses the river ditch or pond as a source of water, pay attention to that all the ends of the suction pipe are not in the water. In order to avoid inhaling stones or more sand and drift debris, the suction pipe end is generally provided with a filtering device, and it is forbidden to remove the filtering device during the water absorption. If the water source is shallow, it is necessary to dig up the water absorption area in advance so as to ensure that it does not contain impurities and air. The water pump requirements for different sprinklers are different. The clean water pump requires no impurities in the water. The turbid water pump requires no stones and excessive sediment in the water. Every time the centrifugal pump absorbs water, a certain amount of water must be added to the pump. After the addition, the water inlet must be closed. When the self-priming pump is used for the first time, it is necessary to add water, and it is not necessary to add water later. The water inlet system must maintain a certain degree of vacuum before it can suck water into the tank. Inlet pipe system must be sealed reliably, the hose can not be damaged, the pipe can not have cracks, otherwise it will have a phenomenon of air leakage, it will result in the case of not drinking water. Before the water sprinkling vehicle or water sprinkling, the power take-off device must be parked. Before the advent of winter, the water in the pumps and pipes should be vented to prevent freezing. The northern part of the country is generally no longer under construction during the severe winter. Therefore, after the construction is completed, the water in the pump and the water pipe will be drained immediately to prevent future problems. The front sprinkler of the sprinkler is located at a lower position, close to the ground, and the spray pressure is relatively large, which can be used for flushing the road surface; the position of the rear sprinkler is relatively high (the sprinkler is generally installed on the left and right sides of the sprinkler), and the sprinkler surface is wide, and can be used for highway construction and watering. When the rear nozzle is used, the front nozzle should be closed; when using an adjustable nozzle, the width of the sprinkler can be adjusted as needed. The wider the sprinkler width, the lower the amount of intermediate overlap and the more uniform the sprinkler density. During the process of use, lubrication points of the transmission assembly should be regularly lubricated, and the joints should be tightened frequently to ensure normal use. The water tank of the sprinkler truck is provided with a sewage pipe. The inlet of the pipe is the lowest point of the water tank. After a period of use, the discharge pipe switch should be opened periodically to remove the accumulated debris from the tank until the water becomes clear. Now many manufacturers produce sprinklers, sprinkler announcements are also quite a lot, the user must look up the exemption announcement at the time of purchase, so as not to mistakenly buy the sprinkler without exemption and more costs. Aluminum Fireproof Panel is a kind of Aluminum Composite Panel.It has fireproof character and apart from it,it also have many other advantages.Such as 1. Light weight: aluminum plastic plate is composed of aluminum and plastic core material with low density. Therefore, compared with aluminum (or other metals) with the same rigidity or thickness, its quality is smaller, and its quality is much smaller than that of glass and stone. Pe Aluminum Composite Panel,Pvdf Aluminum Composite Panel,Acp Aluminum Composite Panel,Fireproof Aluminum Composite Panel Trumony Aluminum Limited , https://www.szaluminumcoil.com
2. Add water diversion
3. The inlet pipe must be vacuumed
4. Parking stalls
5. Winter water release
6. Watering precautions
7. Lubrication and fastening
8. Regular sewage
2. Good rigidity: the aluminum-plastic plate skillfully uses the mechanical principle of I-beam structure and endows it with unique mechanical properties. In addition, the aluminum-plastic plate is compounded under high-temperature conditions, and in the whole processing process, the two-layer Aluminum Plate is in a certain tension state
3. Rich color and strong decoration: the layer surface of aluminum-plastic plate can be made into various colors, and the pattern design matching for all purposes can be carried out