Advantages at a glance: The newly designed milling drum - 100% Bomag design, production increased by 30%, fuel consumption reduced by 7% The heat-treated high-quality wear-resistant material and the arrangement of the cutter head on the milling drum ensure the high-quality efficiency of the Bomag milling machine, and the most advanced design is improved according to the actual experience to ensure the best rotor performance. , lower wear. 1. The edge of the milling drum is designed with wear-resistant edge plates, which are hard chrome alloys, which provide extra protection for the milling drums. 2, from the side of the cutter head can be easily and quickly knocked out the cutter head, speeding up the cutter head replacement time 3, the knife holder is suitable for all types of cutter heads 4, symmetrical design, the throwing plate can be used twice, reducing the cost of use by half 5, the best torque distribution, the operation control panel has a three-speed switch to adjust the milling drum speed, set the milling depth, so that the milling drum can work in the best torque range, while getting as much walking as possible Speed, so the surface quality of the milling plane is high, the milling speed is fast, and the milling drum wears little. 6, fuel consumption reduction: up to 7% 7, uniform cutting 8, low vibration The Bomag BMS15 tool unit offers the best cutting capacity, the longest service life and the most advanced milling technology. 1. Specially quenched steel with long service life 2, the force is transmitted through the tapered contour and the interlocking buckle, which is more stable and stable. 3, the contour of the knife seat design has small resistance, large cutting force and small wear 4, the thread is designed in the wearing part of the wearing part, if necessary, can be quickly replaced 5, cone insert type, can be quickly replaced 6, replace the tool holder, only 100NM of torque, very labor-saving 7. A narrower body than the competitor, higher cutting performance 8, replace the entire new tool holder system only 25% of the original design time, save time and efficiency 9, the required removal tools are less than competitive brands (This article is from Bomag)
PVC sheet is a widely used and popular material. PVC Film can be divided into food grade and industrial grade, and it can be made into transparent, colorful, anti-static, gold-plated, flocking, etc. For vacuum forming, its main characteristics are high transparency, good surface gloss, less crystal points, small water lines, wide use, strong impact resistance, and easy molding. The finished product meets the US FDA and Japanese PL food hygiene standards. It is widely used in the outer packaging of toys, food, electronic products, medicine, electrical appliances, gifts, cosmetics, stationery and other products.
The main classification of blister products Pvc Food Grade Film,Polyolefin Film Products,Fresh Produce Packaging Film,Transparent Pvc Films Roll Shandong Top Leader Plastic Packing CO., LTD , https://www.sdzlplastic.com
1. If classified according to the thickness of the material, it can be divided into
A. The thickness of ordinary thin blister is 0.14~5.0mm-mainly made of various materials and effects such as PVC, PP, PS (HIPS), PET (including APET and PETG), PE, BOPS and recyclable paper trays Folding, half-folding, three-folding, cylinder, folding box, heaven and earth box, high frequency and other non-thermoformed blister products are widely used in food, medicine, electronics, toys, computers, daily necessities, cosmetics, machinery hardware and other industries.
B. The thickness of the special thick blister is 0.14~5.0mm-mainly the plastic injection products with various materials and effects such as PVC, PP, PS (HIPS), PET), ABS, PC, PE, etc.
The reason for not classifying the types of materials is mainly considering that there are some differences between the materials used in ordinary thin blister and special thick blister, but PVC, PP, PS and PET are all in these two types of blister products. To have a role to play!
PVC hard film has moderate toughness and is not easy to burn. It will produce chlorine when burned, which will affect the environment. PVC is easy to heat and can be sealed with a sealing machine and high-frequency machine. It is the main raw material for producing transparent plastic products.
PS hard film has low density, poor toughness, easy to burn, and will produce styrene gas (a harmful gas) when burned, so it is generally used to produce various industrial blister trays.
PET hard film has good toughness, high transparency, easy to burn, and does not produce harmful gas when burned. It is an environmentally friendly material, but the price is high, and it is suitable for high-end blister products. The blister blister in European and American countries generally requires PET hard film, but It is not easy to heat seal, which brings great difficulties to packaging. In order to solve this problem, people compound a layer of PVC film on the surface of PET, named PETG rigid sheet, but the price is higher.
