Sewage suction vehicle suction tire winter tire inspection and maintenance The weather is getting colder, and parts of the north have long snowed. The whole country will soon have to enter the winter. In the winter when ice and snow conditions and icy roads began to appear, road transport began to become difficult. Special vehicles such as suction trucks and suction trucks on the road can easily cause slipping or steering failure after braking. The harsh environment continues to test the driving technology of special vehicle drivers such as sewage suction trucks and suction trucks. It also tests the sewage suction truck The performance of special cars such as cars. It is more and more important for the winter vehicle tires to meet these difficulties. It also needs timely inspection and maintenance. Icy and snowy roads are difficult to drive. Careful attention may be required if they are not careful. Special car users such as suction trucks and sewage trucks should be very troublesome on such roads. In order to avoid unnecessary trouble, winter tire preparation must be prepared. ,in case for need. ◠It is good to deal with ice-slip road with a snow chain Special vehicles such as sewage suction trucks in the winter, such as sewage suction trucks, are equipped with a snow chain and are used when extreme road conditions are encountered. Rainy snow in the north, the road is prone to freezing, the anti-skid chain strengthens the grip, although the brake on the particularly slippery road has slipping phenomenon, it is much better than the no-load effect, and it is safer to drive in the winter. ◠tire pressure should not be too large or too low There is a large temperature difference during the winter daytime and tire pressure is easily changed. The level of tire pressure directly affects the performance and reflection of the tire, and affects the fuel consumption and service life. Sewage suction trucks and other special vehicles in the car must keep the tire pressure within a reasonable range. The pressure is too high and it is easy to puncture the tires. The scope of the grip is reduced and the friction of the vehicle is not enough. Tire pressure is too low to easily wear the tire, the grip area is also limited, the same as the brake effect. The rapid wear of the sidewall causes the tire to be more easily scrapped. ◠Tire pattern needs to check the debris often clean up Tyre rubber will become hard and brittle in the event of cold, friction is reduced, and it is easy to leak and puncture tires. To ensure safety and reduce wear, tires should be changed regularly. The tread pattern design is rigorously tested. Do not change the tire size or install it in the opposite direction. Always inspect and clean foreign objects inside the tire tread of special vehicles such as suction trucks, such as stones and sharp objects, to avoid being penetrated by foreign objects at high speed or in bumps. The uneven wear of the tread pattern is easy to slip on the ice-slip surface. The grip is not strong, and the wear of the tread pattern is often detected in winter. The braking force is not enough to be replaced in time. ◠Fragile inner and outer sidewalls require careful inspection and maintenance The tire wall is a fragile part of the tire, and the puncture of the vehicle is generally caused by scratches and scratches. Care should be taken to carefully inspect both sides, especially where it is difficult to see on the inside. Special sharps, such as suction trucks and suction trucks, may cause direct scratches when driving at high speeds. These injuries may bring unexpected accidents at any time. Danger. ◠Postscript: “The journey of a thousand miles begins with a single step.†Does a special car tire such as a suction truck or a suction truck do not equal human feet? Long-term running in the north and south, how do you do not have a pair of good shoes. In the winter, we also wear a pair of cotton shoes to wear, not to mention our safe suction trucks and other special vehicle tires. The suction truck manufacturer reminds you to use the tires properly for maintenance testing, making it safer to drive in winter! [Dealer]: Manager Wang http:// With the development of die casting industry and foundry, the requirement of Metal Abrasive has became bigger and bigger. Generally, there are many types of Metal Abrasive, like Stainless Steel Shot, Steel Shot, Copper Shot, Aluminium Shot, Zinc Shot. They all have their own advantages. When shot blasting, it is very important to choose suitable media. Otherwise, it can not only get good effects on surface treatment but also increase the cost. Connect us to learn more about it and Longlived Metal Abrasive will help you to save cost and bring you more profits. metal abrasive media,surface treatment,surface finished,metal surface fishing,metal surface treatment Longlived Metal Products Co ., Ltd , https://www.longlivedmetalproducts.com
[Company Name]: Hubei Dicheng Special Sanitation Equipment Co., Ltd.
[Corporate Address]: Beijiao Industrial Park, Suizhou City, Hubei Province
[mobile phone number]: 13908662884
[Contact QQ]: 1305539635
[This information has been verified and certified by China Automotive Network, true and valid]