First, the water caused by the impact and failure Moisture is absorbed by the compressor moist air, the formation of the cooling. Moisture makes pneumatic components rusty, affecting the action of pneumatic components. The effects of moisture are as follows: 1. Piping. Resulting in rust inside the pipe; pipe corrosion, resulting in air leakage, container rupture; water retention at the bottom of the pipeline caused by insufficient air flow, pressure loss increases. 2. Components. Pipe rust, accelerate the filter mesh plug, so that the filter can not work; tube rust within the valve, causing poor performance, air leakage; rust bites the components bite, can not be smooth operation; directly affect the components of pneumatic components, Resulting in poor conversion, air leakage and instability; water droplets invade the actuator internal, resulting in poor performance; water droplets into the internal components, so that can not operate smoothly; water droplets flushing lubricants, poor lubrication, valve failure, the implementation of unstable components ; Stagnant water droplets caused by inadequate traffic flow, pressure loss increases; the phenomenon of water hammer damage caused by components. 3. Environment. Discharge water released from the exhaust port, pollute the environment. Faults caused by moisture can be used to deal with failure is the removal of water, that is, the compressor outlet temperature dropped to make the water contained in the water droplets were analyzed and excluded. For this purpose, a cooler and separator should be installed and installed after the compressor, and an air filter should be installed in the compressor population. Horizontal pipe has a certain slope, the drain valve installed at the low end. Install a dryer outlet. Water removal measures can be used as follows. a. Adsorption water removal method: Adsorption of water with a strong adsorption capacity of materials, such as silica gel, aluminum and molecular sieve b, pressure dehumidification: to increase the pressure, so that the volume decreases, the temperature drops, and thus precipitation of water droplets. c. Mechanical water removal: mechanical barrier, cyclone and other water removal. d. Frozen water removal: Cooling equipment to make the air cooled to below the dew point, the water vapor condensation into water precipitation. Second, the oil caused by the impact and failure Compressor oil mist mixed with compressed air, and with the heat sent with the compressed air, compressed air is the cause of oil. The impact of oil is as follows: 1. Seal deformation. Sealing ring shrinkage, air leakage valve failure, the lack of output power of the implementing element; sealing ring bubble swollen, increased friction, the valve can not move or lack of output force of the actuator; ring hardening, friction surface wear, air leakage increased Large; friction increases, the valve and actuator failure. 2. Environment. Industrial raw materials directly contact with the air chemicals place the nature of the chemical changes in raw materials; industrial furnaces and other places in direct contact with the fire caused a fire risk; use of air due to the nozzle of the measuring instruments and plugging failure; require extreme oil environment, due to the valve and actuator Sealing part of the oil leakage caused by environmental pollution, oil removal method is the use of oil filter. For example, use a centrifugal filter to remove oil mist particles, adsorb with activated carbon, or degrease with a porous filter. Third, the dust caused by the impact and fault compressor suction dusty air into the pneumatic device, resulting in friction pneumatic components, damage and increase friction. The effects of dust are as follows: 1. Control element. Control element friction and wear and stuck, malfunction and can not change direction; affect the stability of the regulator. 2. Executive components. Friction and wear the actuator and stuck, the action failure; reduce the output force. 3. Amplifiers and other throttling pieces of pneumatic components. So that the throttle baffle orifice clogged due to oil pollution and failure, dust removal method is installed in the compressor suction air filter, air filter before entering the air filter, the filter on a regular basis to clean or replace.

Hook

A lifting hook is a commonplace in the Crane industry, with unique functions to Grab objects. When selecting a hook for your crane, safety is often the most important consideration. This dictates that materials for hook is made from top-in-class carbon steel. The integrated manufacturing process and advanced techniques make sure that we produce world-class hooks.

Advantages:

Ergonomic design

Material: alloy steel

Treatment: Heat treating

Available with the safety latch and check points

Proof test load: twice the working load limit

Minimum breaking strength: four times the working load limit

Foolproof safety lock ensure operation safety

Convenient to install

Compact design with outstanding performance

Marked on the hook are the rated working load and product classification

Load capacity:50kg-60kg

Application

Port, waste management, wind power, automobile, transformer, storage and logistics, steel, container ,tunnel, architecture, metallurgy and shipbuilding industries.

Crane Lifting Hook,World-Class Hooks,Ergonomic Designed Hooks,Lifting Hook,Alloy Steel Hook

Eurocrane (China) Co., Ltd. , https://www.eurocranegroup.com