Electromagnetic flowmeter on-site common problems and handling Electromagnetic Flowmeter: Under normal circumstances, the user's fault will be reflected: 1. Measurement fluctuations 2. Inaccurate measurement 3. There is medium but the meter shows zero 4 no display or display no output The common solution is: 1. The reason for the fluctuation of the measured value may be: Wiring problem (applicable to newly installed flow meter), under normal circumstances shielded wire is not connected; User process problems, may be not satisfied with the pipe (there may be a pre-installation does not meet the installation conditions, must ensure that the full pipe; later use in the pipeline does not install the exhaust valve helium) Whether the valve at the front end of the flowmeter is fully open may cause fluctuation if it is not fully opened Check if the conductivity is too low, if the conductivity is low it may lead to fluctuations Check whether the flow meter is filled with water. If it is flooded, it can be judged as broken. Flowmeter quality problems, measuring sensor resistance is normal, use GS8 test converter is normal, conditions allow to replace a normal try 2. The reason for inaccurate measurements may be: The user will connect the wrong line, check the wiring Check whether the sensor and the converter meter number are the same. If not, check the pipe diameter, GK, GKL, and excitation frequency. The user will bypass the tube is closed Whether the medium is a medium that is prone to fouling, and if it is susceptible to scaling it can also cause inaccurate measurements. 3. The reason why the media flow meter displays zero may be: Check the connection line is normal, there may be interrupted middle line Check whether full pipe is guaranteed Make sure the medium flows through the sensor and check that the front and rear valves are open Check if the conductivity of the user's medium is within the proper range. If the conductivity is low, check if the threshold is too high. 4. The reason why the meter has no display or no output is displayed may be: Measure whether the user's power supply is qualified Check the user's output wiring is correct, use a multimeter to measure the current output Check if the fuse in the converter's movement is broken (IFC300 has two fuses, power and output insurance; IFC100 has one insurance) Check whether the display screen and the movement of the movement are plugged in, or if the display is broken, there is a condition that you can try using a normally displayed screen, or get back the company test . Shanghai Fanmai Industrial Development Co., Ltd. is now acting for a number of well-known foreign brands, focusing on the marketing and sales of imported sensors and instruments, and adhering to the development direction of multi-category, multi-brand, differentiated and enthusiastic services. Since its establishment, the company has been providing its customers with high-quality, high-performance imported automation products with perfect business management and sincere professional services. Facing the chaotic parts market, the commodities it has been supplying have been trusted and selected by a large number of professional manufacturers . Shanghai Fanmai Industrial Development Co., Ltd. not only provides genuine imported products, we also provide maintenance services. If you have any questions, please call us or choose to leave a message. Exterior Door Handle For European Exterior car door handles lets you access your car`s cabin. without them, doors are hard to open. Exterior door handles come in various shapes and styles but the operation is generally the same; pulling the lever out releases the hook from the vehicle frame`s latch. Exterior Door Handle For European,Renault Outside Exterior Door Handle,Alfa Romeo Outer Handle Replacement,Koleos Outside Handle Repair RUIAN XINGTING AUTO PARTS CO.,LTD , https://www.xingtinghandle.com
Here are some types of OE replacement exterior car door handles: pull up, pull out, and trigger.
There are two main materials used in manufacturing exterior door handles-plastic and metal.
Both materials come with different finishes, such as smooth black, textured, chrome and primed. Textured handles offer better grip even when wet, while smooth black and chrome blends with the color of your car. Primed handles are ready-to-paint pieces, which are perfect if you want to match your vehicle`s unique color.
These application-specific parts are made to look like and seemlessly replace exterior door handles, reinforcement brackets, and more.
- Stock Appearance: these replacement exterior door handles were specifically designed to look and function the same as the original handle on particular vehicles, and to match the original dimensions and specifications
- Great Value: OE quality at a lower price