Centrifuge Spray Drying Equipment/Machine for Natural Pectin

MATERIAL



WORKING PRINCIPLE
Filtered and heated air goes into air distributor on the top of the dryer, and spirals into drying room uniformly. Going through the high-speed centrifugal atomizer on the top of tower, the liquid (rotates) sprays into extremely fine mist liquid beads, and can be dried completely in a short time in co-current contact with hot air. Finished products exhaust continuously from the bottom of the drying tower and cyclone separator, while waste gases are vented by the fan. 

FEATURES
1. Fast drying speed; greatly increasing the surface area of the material after the liquid is atomized; it can instantly evaporate 95% -98% of water in the stream of hot air; it takes only a few seconds to complete drying, which is especially suitable for drying heat sensitive materials. 
2. Our products have a good uniformity, mobility and solubility, high purity and good quality.
3. Simplified production process, easy to operate and control. Liquid of 40-60% moisture content (up to 90% for special materials) can be dried into powder products at a time, without crushing and screening after drying, which reduces production process and improve product purity. The size, bulk density, moisture can be adjusted within a certain range by changing operation conditions. It is convenient to do control and management. 

APPLICATION
Chemical industry: sodium fluoride (potassium), alkaline dyestuff and pigment, dyestuff intermediate, compound fertilizer, formaldehyde silicic acid, catalyst, sulphuric acid agent, amino acid, white carbon black, etc.
Plastic resin: AB, ABS latex, urea resin, phenolic resin, dense glue (urea) formaldehyde resins, polyethylene, polyvinyl chloride, etc.
Food industry: fat-rich milk powder, lancet protein, cocoa milk powder, babymeal, hunting blood meal, egg white (yellow), etc.
Food and plants: oats, chicken juice, coffee, instant tea, seasoning meat, protein, soybean, peanut protein, hydrolyzate and so on.
Sugar: corn syrup, corn starch, glucose, pectin, malt sugar, potassium sorbate, etc.
Ceramics: aluminium oxide, ceramic tile material, magnesium oxide, talcum powder, etc.

DETAILS


SCHEMATIC DIAGRAM


TECHNICAL PARAMETERS

Note: the amount of water evaporation depends on the factors of material characteristics, inlet and outlet temperature. Water evaporation curve is shown above (for reference of selection) when the outlet temperature is 90ºC. With the constantly updated, relevant parameters will change without prior notice.
 
ORDERING INFORMATION
1,Name and physical properties of liquids; Solid content (or water content), viscosity, surface tension, PH value.
2,After drying, the maximum value of powder capacity, residual water content, particle size and temperature.
3,Volume of production, opening times of the day.
4,Available energy: steam pressure availability, electric capacity, coal, oil and gas availability.
5,Control requirement: whether you need to self-control inlet and outlet temperatures.
6,Powder collecting requirements: whether you need to install a pouched trapper.
7,Environmental requirements for exhaust emissions.
8,Other special requirements.

COMPANY SHOW


CERITIFICATES



SERVICES
pre-sale service
We Invite customers to visit our company and communicate on technical requirements face to face.
sale service
Responsible for debugging the equipment according to customers' requirements of various technical data. Our engineers will train our customers about equipment features and operation key points to make sure the equipment running in the best condition.
after-sale service
We provide installation, debugging, maintenance, training and other services; Provide relevant technical data, equipment, software and related GMP certification materials;Set up after-sales service hotline, and arrange personnel to visit customers every year to know more customer needs,like customer operation problems in the process of production equipment.
quality promise
Our company promises strictly operate the ISO9001 quality system certification standards and pharmaceutical equipment GMP audit requirements,promise we provide new equipment. Advanced technology,good quality.Equipment operation safe reliable, affordable, easy to maintain.
 
Equipment warranty period is one year,all the parts for the equipment choose well-known brand.
During the warranty when equipment have problem in quality like equipment failure and damage, our company offer free maintenance or replacement.

MATERIAL



WORKING PRINCIPLE
Filtered and heated air goes into air distributor on the top of the dryer, and spirals into drying room uniformly. Going through the high-speed centrifugal atomizer on the top of tower, the liquid (rotates) sprays into extremely fine mist liquid beads, and can be dried completely in a short time in co-current contact with hot air. Finished products exhaust continuously from the bottom of the drying tower and cyclone separator, while waste gases are vented by the fan. 

FEATURES
1. Fast drying speed; greatly increasing the surface area of the material after the liquid is atomized; it can instantly evaporate 95% -98% of water in the stream of hot air; it takes only a few seconds to complete drying, which is especially suitable for drying heat sensitive materials. 
2. Our products have a good uniformity, mobility and solubility, high purity and good quality.
3. Simplified production process, easy to operate and control. Liquid of 40-60% moisture content (up to 90% for special materials) can be dried into powder products at a time, without crushing and screening after drying, which reduces production process and improve product purity. The size, bulk density, moisture can be adjusted within a certain range by changing operation conditions. It is convenient to do control and management. 

APPLICATION
Chemical industry: sodium fluoride (potassium), alkaline dyestuff and pigment, dyestuff intermediate, compound fertilizer, formaldehyde silicic acid, catalyst, sulphuric acid agent, amino acid, white carbon black, etc.
Plastic resin: AB, ABS latex, urea resin, phenolic resin, dense glue (urea) formaldehyde resins, polyethylene, polyvinyl chloride, etc.
Food industry: fat-rich milk powder, lancet protein, cocoa milk powder, babymeal, hunting blood meal, egg white (yellow), etc.
Food and plants: oats, chicken juice, coffee, instant tea, seasoning meat, protein, soybean, peanut protein, hydrolyzate and so on.
Sugar: corn syrup, corn starch, glucose, pectin, malt sugar, potassium sorbate, etc.
Ceramics: aluminium oxide, ceramic tile material, magnesium oxide, talcum powder, etc.

DETAILS


SCHEMATIC DIAGRAM


TECHNICAL PARAMETERS

Note: the amount of water evaporation depends on the factors of material characteristics, inlet and outlet temperature. Water evaporation curve is shown above (for reference of selection) when the outlet temperature is 90ºC. With the constantly updated, relevant parameters will change without prior notice.
 
ORDERING INFORMATION
1,Name and physical properties of liquids; Solid content (or water content), viscosity, surface tension, PH value.
2,After drying, the maximum value of powder capacity, residual water content, particle size and temperature.
3,Volume of production, opening times of the day.
4,Available energy: steam pressure availability, electric capacity, coal, oil and gas availability.
5,Control requirement: whether you need to self-control inlet and outlet temperatures.
6,Powder collecting requirements: whether you need to install a pouched trapper.
7,Environmental requirements for exhaust emissions.
8,Other special requirements.

COMPANY SHOW


CERITIFICATES



SERVICES
pre-sale service
We Invite customers to visit our company and communicate on technical requirements face to face.
sale service
Responsible for debugging the equipment according to customers' requirements of various technical data. Our engineers will train our customers about equipment features and operation key points to make sure the equipment running in the best condition.
after-sale service
We provide installation, debugging, maintenance, training and other services; Provide relevant technical data, equipment, software and related GMP certification materials;Set up after-sales service hotline, and arrange personnel to visit customers every year to know more customer needs,like customer operation problems in the process of production equipment.
quality promise
Our company promises strictly operate the ISO9001 quality system certification standards and pharmaceutical equipment GMP audit requirements,promise we provide new equipment. Advanced technology,good quality.Equipment operation safe reliable, affordable, easy to maintain.
 
Equipment warranty period is one year,all the parts for the equipment choose well-known brand.
During the warranty when equipment have problem in quality like equipment failure and damage, our company offer free maintenance or replacement.

At this time of Chair Hardware should be flat or flip open, chair hardwares include shaft to open chairs or hinge and the chairs shut device such as pin.In order to improve the chairs the wind strength, it is widely used outside the chairs. But hinge must be exposed outside the chairs, the wind and rain erosion resistance of hinge became a problem. Now some of the more than one hundred old buildings in Europe, you can also see 10 times larger than present ordinary hinge of metal hinge, the hinge on the style and ancient European construction is harmonious.Outside the chair hardware of the another question is to prevent the casement of open type in free violently movement under the action of wind, so have the so-called limiter, the limiter in many ways are prone to failure parts.

Chair Hardware

Chair Hardware,Aluminum Die Casting Chair Hardware,Chair Hardware Parts,Chair Accessories Hardware

NINGBO ZHENHAI BOLANG METAL PRODUCT FACTORY , http://www.blcastings.com