We all know that the necessary components of the crane are the power take-offs. The power take-off is an important part of the small crane. It mainly draws power from the chassis transmission to drive the hydraulic pump, transmits the power of the internal combustion engine of the carrier to the transmission, and then The power take-off is used to take out the power from the intermediate shaft of the transmission, and then the hydraulic pump is driven by a special drive shaft to supply the pressure oil to other components of the crane to complete the lifting operation. In fact, the crane is mainly based on the principle of physical leverage, in a certain range through vertical and horizontal lifting handling heavy objects. Generally, it is mainly used for lifting relatively heavy articles, and sometimes it is also possible to hoist loose materials and liquid materials with suitable spreaders. The work of the crane is generally characterized by intermittent movements, that is, in the state of a work cycle, the materials are taken, transported, unloaded, and the like in order to perform alternate work. Each institution is often in the starting, braking, and working directions. The power take-off device is generally connected with a transmission shaft or directly connected with a gear pump and completes the lifting work in combination with other components. The working principle of the power take-off of the crane (operation method): 1. After the internal combustion engine is started, the power take-off control device first needs to run at low speed for a period of time. After the temperature of the internal combustion engine and the pressure of the lubricating oil are normal, the power take-off device can be operated together with the remaining components. When it is necessary to drive the hydraulic pump, it is necessary to close the power switch of the power take-off and then depress the clutch pedal. When the power indicator light 12 is lighted, it indicates that the hydraulic pump has started working. At this point, the speed of the hydraulic pump can only be controlled by the on-board cab. At this time, getting off the accelerator pedal will not have any effect. When it is necessary to stop the work of the hydraulic pump, it is necessary to step on the clutch pedal in the getting off cab, and then turn the variable power take off switch to the off position. When the power indicator light goes out, the off accelerator pedal will resume control of the engine speed. The function of the crane can be transferred. 2. Manually operated power take-offs are mainly used on wheeled cranes. Power take-offs are bolted to the power take-off window of the crane's transmission. It is mainly through a three-axle gearbox through the large gear on the active tower gear. Mesh with the power output gear of the transmission's countershaft. The power of the engine is mainly input through the active tower gear, and then it is transmitted through the gears on the intermediate shaft and the main shaft. Finally, it is output by the connecting flange on the main shaft. Finally, the universal drive shaft drives the hydraulic pump. Use the shift lever to toggle the shift fork shaft to move the sliding tower gear to complete the in-gear (combination) and the off-gear (disengagement). When the crane is running, the hydraulic pump must be disconnected from the engine. Combined control of power take-off, and some use of rods in the cab to operate, that is, manual gear and pick off; most use electromagnetic control power take-off gear, pick off. At present, most domestic power take-off devices are used on dump trucks, so the requirements for power take-off devices are relatively single. In Europe, North America and other countries, due to the relatively high requirements for power take-offs of special vehicles, manufacturers of power takeoffs will design multi-output power take-off devices or power take-off devices with clutches to increase the multi-functional operation of cranes. . I hope the above article is helpful to you! More related content You can follow our official website. Pulverizers are machines that pulverize large solid materials to the required size. Pulverizer Machine,Crushing Machine,Milling Machine,Grinding Mill, Grinding Machine JIANGYIN CITY XUAN TENG MACHINERY EQUIPMENT CO.,LTD , https://www.xuantengmachine.com
According to the size of the crushed material or the crushed material, the mill can be divided into coarse crusher, medium crusher, fine mill and superfine mill. There are four kinds of external forces applied to the solid in the grinding process: pressing, cutting, impact and grinding. Press rolling is mainly used in coarse and medium crushing, suitable for the crushing of hard materials and bulk materials. Shearing is mainly used in fine crushing, suitable for the crushing of ductile materials. Impact is mainly used in medium crushing, fine grinding, ultrafine grinding, suitable for crushing brittle materials. Grinding mainly in fine grinding, ultrafine grinding, suitable for small pieces and fine particles.
The crusher makes use of the high speed relative motion of the movable tooth plate and the fixed tooth plate, so that the crushed object can be crushed by the comprehensive action of tooth impact, friction and the impact between the materials. The crusher is suitable for crushing Chinese herbs, precious medicinal materials, ores and chemical raw materials in small batches in various varieties, alloys, metallurgy, geology, scientific research and other units.
The pulverizer machine has the advantages of simple structure, solid, stable operation and good crushing effect. The pulverized material can be discharged directly from the grinding chamber of the main machine. The particle size can be obtained by replacing the mesh screen with different aperture. The powder collecting chamber adopts the completely closed silencer structure, which can effectively reduce the working noise. In addition the machine is all stainless steel. The inner wall of the casing is machined to achieve smooth surface, which changes the phenomenon of rough inner wall and powder accumulation of the previous models, so that the production of drugs, food, chemical industry and so on is more in line with national standards and meet the requirements of GMP.